Best Watch Winder for Bedat & Co. | Tempus Luxury
Bedat & Co. was founded in Geneva in 1996 by Simone Bédat, who set out to create a maison devoted to feminine watchmaking. With Art Deco lines, mother-of-pearl dials and elegant tonneau cases, Bedat watches are jewellery and horology in equal measure — numbered rather than named, from the 100s to the 800s.
Bedat automatics reward a winder that can handle both 725 TPD clockwise and 650 TPD bi-directional calibres — sometimes within the same collection. Match the setting to the model number and your Bedat will never miss a beat.
Bedat & Co. TPD Requirements
Bedat & Co. splits into two camps: many references (Model 114, 314, 708 and others) wind at 725 TPD clockwise, while the rest (Model 388, 747, 888 and others) prefer 650 TPD bi-directional. Check your reference number against the table.
| Model | Recommended Setting |
|---|---|
| Bedat & Co. Model 314 | 725 TPD, clockwise |
| Bedat & Co. Model 388 | 650 TPD, bi-directional |
| Bedat & Co. Model 114 | 725 TPD, clockwise |
| Bedat & Co. Model 888 | 650 TPD, bi-directional |
| Bedat & Co. Model 767 | 650 TPD, bi-directional |
Tap any model above for its full settings page, including movement reference and setup advice.
What to Look for in a Winder for Bedat & Co.
A winder offering 725 TPD clockwise — an uncommon setting many basic winders cannot do — alongside the standard 650 bi-directional. If you own models from both camps, independent per-rotor settings are essential.
Beyond the numbers, the fundamentals still apply: whisper-quiet operation so the winder can live in a bedroom, a holder that grips a smaller ladies' case without marking it, and an elegant finish worthy of the watches inside. Every Tempus winder is built around these, with programmable TPD, three winding directions and a 3-year warranty as standard.
Three Tempus Winders for Bedat & Co. Owners
- Tempus Single with Remote Control (£296) — a discreet home for one treasured Bedat.
- Tempus 2 Biometric (£446) — fingerprint security for a pair of Bedats.
- Tempus 4 Touch Screen (£596) — four independently set rotors for a varied collection.
Why Bedat & Co. Owners Bother With a Winder
A Bedat is often an occasion watch — worn for evenings out, then rested for days. A winder means it is always running, always correct, always ready, with the movement's lubricants kept evenly distributed between wearings. For a watch bought as jewellery as much as horology, perpetual readiness is the point.
Single vs Multi-Watch for Bedat & Co.
One Bedat for special occasions? A single winder is perfect. But collectors of the maison often own several numbered references — and with the split between 725-clockwise and 650 bi-directional calibres, a double or 4-watch unit with independent settings keeps each one correctly wound. One power supply, one footprint, every Bedat ready.
Frequently Asked Questions
Do Bedat & Co. watches need a watch winder?
No automatic watch needs a winder — but without one, your Bedat will run down after a couple of days off the wrist. For an occasion watch, a winder means it is always ready when the occasion arrives.
What happens if the TPD setting is wrong?
Nothing dramatic. Modern automatics have a slipping mainspring that prevents overwinding, so an incorrect setting cannot damage the movement — the watch simply may not stay fully wound. Use the table above as your starting point.
Can Tempus winders do 725 TPD clockwise?
Yes. Tempus winders offer programmable TPD with clockwise, counter-clockwise and bi-directional modes, covering both the 725 TPD clockwise and 650 TPD bi-directional Bedat & Co. references.
What warranty do Tempus winders carry?
Every Tempus watch winder includes a 3-year warranty. Tempus can also repair any Tempus-brand winder even after the warranty period has ended.
For model-specific settings, see our TPD settings guide.
What TPD setting does a Bedat & Co. Model 314 need?
The Bedat & Co. Model 314 needs 725 TPD clockwise. Many Bedat references share this setting, while others — like the Model 388 — need 650 TPD bi-directional, so always check your model number.
Why do some Bedat models wind clockwise only?
It comes down to the calibre inside. Bedat & Co. has used various automatic movements over the years, and several wind in the clockwise direction only at 725 TPD. Your Tempus winder's clockwise mode covers them all.
Can I wind two different Bedat models together?
Yes, with independent settings. A Model 314 (725 clockwise) and a Model 388 (650 bi-directional) need different settings, so use a multi-watch Tempus winder and set each rotor to match its watch.
Will a winder damage my Bedat & Co.?
No. Modern automatic movements have a slipping mainspring that prevents overwinding, so a winder cannot damage your Bedat & Co. Tempus winders use quiet Japanese and German motors and come with a 3-year warranty.
What is the best Tempus winder for a Bedat pair?
The Tempus 2 Biometric (£446) — two independently set rotors for the mixed 725/650 requirements, with fingerprint security for valuable pieces.